Products /


 

Dekor
Line Textured Ready Mixed Plaster

Product Definition
Polymer emulsion based, line textured, trowel applied, coarse, ready mixed interior and exterior plaster.

Application Areas
> On exterior mineral surfaces such as concrete, mortar, cement panel, etc., on previously painted surfaces and also on interior surfaces for decorative purposes.

Features
> High water vapour permeability allowing building to breathe.
> Long lasting; resists to UV rays, rain, heat and frost, thus retains its original properties for years without cracking, blistering and fading.
> Alkali resistant.
> Horizontal, vertical or circular line textures can be obtained by movements of trowel.
> Water resistant.
> Solvent free and practically odourless.
> Water thinnable and ecologically compatible.

Colors and Textures:


Technical Features
(at 23°C and 50% RH)

General Data:
Colors: Available in 144 colors of the exterior color chart. Tintable by Renk Ustası
Texture: Line textured
Composition: Polymer emulsion based
Thinner: Water

Application Data:
Application Temperature Range: (+5°C) - (+35°C)
Drying Time: Surface dry after 24 hours and thoroughly dry after 2-3 days.
Lower temperatures and/or higher relative humidity will lengthen the drying process.
Consumption: Depending on the evenness of the surface approximately 3.3-3.5 kg/m²
Application Tools: Plastic trowel.

Performance Data:
Water Vapour Permeability SD (m) (TS EN ISO 7783-2): Approx. 0.100
Water Absorption (kg/m² h0.5) (TS EN 1062-3): 0.100-0.500
Peeling Strength (KgF) (AFNOR T 30706): > 2.5
Service Temperature: (-30°C) - (+80°C)

TS EN 1062-1: Classification
Film Thickness: Class E5
Grain Size: Class S4
Water Vapour Transmission: Class V1
Liquid Water Permeability: Class W2
Crack Bridging: Class A0
CO2 Permeability: Class C0
Fungi and Algae Resistance: Class K2

Application Instructions
> The substrate must be cleaned from dust, dirt, oil and old blistered coatings that may prevent good adhesion. The surface should be made sound, clean and dry. New cementitous substrates must be cured at least 28 days before application. All water insulation precautions should have been taken prior to application.
> Prime the surface with Kale SİLASTAR or Kale ÜNİASTAR in the same color shade of the plaster.
> Mix Kale DEKOR thoroughly, if required add clean water until it reaches application viscosity.
> Spread Dekor evenly on the surface in the thickness of the grain size with plastic trowel.
> Texture by moving the trowel horizontally, vertically and roundly depending on the desired texture.
> Clean the tools with water.
> Ensure that the air and surface temperatures are above 5°C and the surface is rain free during application and 24 hours following the application.
> Do not apply in extremely hot weather, under glaring sun, during strong wind, fog, high relative humidity, imminent rain or frost.
> Hot surfaces should be dampened before application. In order to avoid differences in shades of color, products with the same charge number should be used. In the event products with different charge numbers are to be used, the entire required amount should be mixed prior to application.
> In order to avoid overlapping in large areas or after work pauses, masking tape should be used or an adequate number of applicators should be employed to apply the plaster wet-on-wet without interruptions.

Warnings

> S2 Keep out of the reach of children.
> S24/25 Avoid contact with skin and eyes.
> S46 If swallowed, seek medical advice.

Storage
> Store between 5°C-35°C in its unopened pail.

Packaging
> Available in 25 kg pails.

Quality Documents
TS 7847



Back Back  Top Top Print Print

 

Kale Kalekim Corporate                  Kalekim Facebook Kalekim Blog Kalekim Twitter

Türkçe    > English    Русский