Products /


 

KALEKİM
Tile Adhesive (C1TE)

Product Definition
Cementitious ceramic tile adhesive with extended open time and reduced slip.

Application Areas
> Floor and wall bonding of all types of ceramic tiles, mosaic and decorative bricks on cementitious renders, cementitious screeds and concrete.
> The substrates must be notched or primed with KALEKİM DOLGULU ASTAR before bonding of tiles on existing ceramic tiles.

Features
> High adhesion strength.
> Allows installation of tiles from top towards the bottom.
> Extended open time.
> Easily trowellable.

Video


Technical Features
(at 23°C and 50% RH)

General Data:
Appearance: Grey powder
Shelf Life: 12 months when stored in the original sealed packing in dry place.

Application Data:
Application Temperature Range: (+5°C) - (+35°C)
Mixing Ratio: 6.5 - 8 lt water / 25 kg powder 1.3 - 1.6 lt water / 5 kg powder
Pot Life: Approx. 6 hours
Slip (EN 1308): ≤0.5 mm
Open Time (EN 1346): After 30 minutes ≥ 0.5 N/mm²
Grouting: 8 hours on wall; 24 hours after on floor
Consumption: 3 - 5 kg/m²

Performance Data:
Tensile Adhesion Strength (EN 1348)
-initial ≥ 0.5 N/mm²
-after heat exposure ≥ 0.5 N/mm²
-after immersion in water ≥ 0.5 N/mm²
-after freeze/thaw cycles ≥ 0.5 N/mm²
Service Temperature Range (after final cure): (-40°C) - (+80°C)
Dangerous Substances (EN 12004): Complies
Reaction to Fire: A1

Application Instructions
> Substrates must be sound, free from oil, grease, and sufficiently dry. Cementitious substrates must be cured.
> Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface.
> Wipe the back side of tiles with water if dusty.
> Pour 25 kg of KALEKİM 1051 into 6.5-8 litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application
> Allow to stand for 5-10 minutes to mature. After 1-2 minutes remixing, the paste is ready for application.
> Spread the mortar onto the substrate with notched trowel of which notch size is appropriate to the tile dimension (See Notch Size Recommendation Table). To obtain a good adhesion first apply a thin coat of KALEKİM 1051 with the flat side of trowel, then notch with the toothed side of trowel.
> Open time is 30 minutes. Install the tiles within this period with pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar.
> Dispose mortars of which pot life is expired. Clean tools and hands with water, surfaces with a damp cloth.
> Tiles installed with KALEKİM 1051 must not be subject to water for at least 24 hours.

Warnings

> Since contains cement, irritating to eyes, respiratory system and skin. For further information refer to safety data sheet.
> Indicated consumption is a general information. It may change depending on the application conditions and surface properties.

Storage
> Store in dry medium. Do not stack more than 10 bags on top of each other.

Packaging
> 5 kg polyethylene bag,
> 25 kg multi-ply paper bags.

Quality Documents
TS EN 12004, Class C1TE
C: Cementitious
1: Normal setting
T: Reduced slip
E: Extended open time



Back Back  Top Top Print Print

 

Kale Kalekim Corporate                  Kalekim Facebook Kalekim Blog Kalekim Twitter

Türkçe    > English    Русский